Check tire tread depth with the penny test, the built-in wear bars or a gauge, measure several spots on each tire, and know when NHTSA says to replace it.
How do you check tire tread depth?
Look at the grooves on every tire with a penny, the built-in treadwear indicators or a tread depth gauge, and replace any tire whose tread has worn down to 2/32 of an inch. NHTSA says tires are not safe at that depth. It also says to check tread at least once a month, when you check pressure.
This guide covers the tread check itself. The pre-trip tire check looks at the whole tire, and the used car tire check is for buyers. More upkeep topics are in Tires, Wheels and Brakes.
Where the 2/32 inch limit comes from
NHTSA’s tire guidance names 2/32 of an inch as the point where tires should be replaced. That is the same as 1/16 of an inch. Federal rule 49 CFR 571.109 writes the same depth as 1.6 millimeters (1/16 inch) when it describes the tread wear indicator.
Treat it as a ceiling on wear, not a target. A tire that is just above the limit has almost no tread left to give.
Find the treadwear indicators
NHTSA says tires have built-in treadwear indicators, which are raised sections that run between the tread. When the tread is worn level with an indicator, it is time to replace the tires.
49 CFR 571.139 sets the minimum number. A radial tire for a light vehicle needs at least six indicators, spaced about equally around the tire. Tires on rims of 12 inches or smaller need at least three. The indicators sit in the principal grooves, so look there.
Compare each bar with the tread blocks beside it. If the blocks are flush with the bar, the tire has reached the limit. This check needs no tools, but it only tells you when you have arrived, not how far away you are.
Run the penny test
NHTSA describes the penny test in one line: place a penny in the tread with Lincoln’s head upside down and facing you. If you can see the top of Lincoln’s head, replace the tire.
Try several grooves on each tire. A penny gives a pass or fail at the limit. It does not show a trend, so it cannot tell you whether a tire has months or weeks left.
Use a tread depth gauge for a number
NHTSA’s pages name the penny and the indicators. They do not describe a particular gauge, so follow the instructions that come with yours.
Check the scale first. Some gauges read in 32nds of an inch and some in millimeters, and 2/32 inch equals 1.6 mm. Place the probe in a groove, not on a wear bar, and press the gauge flat against the tread.
Write each reading down. A monthly log shows how fast a tire is wearing, which a penny cannot do.
Measure several points on every tire
One reading can mislead. In the government’s treadwear grading, 49 CFR 575.104 calls for six equally spaced points in each groove, avoiding the treadwear indicators, and then averages them. That is a laboratory method, but the idea carries over.
For a home check, measure a few places across the width and a few around the circumference. Judge the tire by its lowest reading. If the penny shows Lincoln’s head at any spot, NHTSA’s rule says to replace the tire.
| Method | What it shows | Limit |
|---|---|---|
| Treadwear indicator | Whether tread is level with the bar at about 1/16 inch | No number before the limit |
| Penny test | Whether Lincoln’s head is visible at the spot you test | Pass or fail only |
| Tread depth gauge | A reading you can log each month | Confirm its scale and zero first |
| Several spots per tire | Whether wear is even across and around the tire | Needs a reading in more than one groove |
What uneven readings mean
If one edge or one section reads lower than the rest, do not average it away. NHTSA lists irregular wear caused by underinflation or overloading among the reasons to stop using a tire. It adds that rotation can reduce irregular wear and that alignment by a qualified technician helps tires last longer.
See uneven tire wear patterns explained for how to describe a pattern to a shop. Check pressure against the vehicle label, not the sidewall, using the placard versus sidewall guide.
Tread is not the only reason to replace a tire. NHTSA says you cannot see tire aging, so read the date code even when the tread looks fine.
Frequently asked questions
How often should I check tire tread depth?
NHTSA says to check tread at least once a month, at the same time you check pressure. Its new-tire handout adds that you should look at the tread when you rotate tires and before long trips.
Is the penny test accurate enough?
It is a reasonable test of one question: has the tread reached the limit at that spot? It gives no number, so a gauge is better if you want to track wear over time. Whatever you use, test more than one groove on each tire.
Can a tire pass the tread test and still need replacing?
Yes. NHTSA lists physical damage such as cuts, cracks and bulges as separate reasons to stop using a tire. It also says some vehicle and tire makers recommend replacement at six to 10 years regardless of treadwear.
Do I need to check the spare tire’s tread?
Check its pressure with the others. NHTSA says spares age because they are seldom replaced, and that a full-size spare should not replace worn tires except in an emergency such as a flat.
