Choose track day tires by organizer rules, tread condition, weather and heat cycles, and learn what UTQG grades do and do not prove.
How do you choose a safe track day tire?
Choose a tire that the organizer will pass, that suits the weather you expect, and that still has enough tread and life for the driving you will do. A track day is not a race, so the fastest tire is rarely the right first choice.
NASA Arizona says a driver does not need fancy or performance tires to pass tech. Its inspectors look for enough tread to avoid cording before the end of the event, plus sidewall damage such as cracks or bubbles. That is a condition test, not a lap-time test.
What the tech line will look at
The NASA NorCal first-day guidance adds detail. Tread should be above the wear bars. No cords or belts may show. Tires repaired with plugs are not accepted. Hubcaps and beauty rings must come off. NASA Northeast’s FAQ adds that tires should be in matched sets on each axle.
The NASA Arizona page makes the same point from the inspector’s side: the only tire details tech checks are tread sufficient to reach the end of the event and sidewall condition. A new set of ordinary street tires can pass.
Check your event’s rules before you buy anything.
What UTQG grades do and do not tell you
Most passenger tires carry three federal grades under 49 CFR 575.104. A sidewall might read “Treadwear 200 Traction AA Temperature A.”
| Grade | What it measures | What it leaves out |
|---|---|---|
| Treadwear, in multiples of 20 | Relative wear on a government test course | Real mileage, grip and track temperature |
| Traction AA, A, B or C | Wet straight-ahead braking on asphalt and concrete | Cornering, acceleration, hydroplaning and peak grip |
| Temperature A, B or C | Heat resistance on an indoor test wheel | Behavior when underinflated or overloaded |
Treadwear is comparative, not a mileage promise. The rule says a tire graded 150 would wear one and one-half times as well on the government course as one graded 100.
The number also cannot rank dry grip. A low treadwear tire wears faster on the government course, but the regulation does not test lap time at all.
Heat cycles, pressure and tire care
A competition-style tire is often prepared with a deliberate break-in, and that process is a heat cycle. Hoosier’s guidance for its TrackAttack Pro says the first session should last no more than 10 to 15 minutes. The pace starts easy and rises until the final lap is at or near maximum. Then the car comes in and the tires cool at a normal rate.
Hoosier suggests 4 to 7 laps for the run-in, each about 7 to 10 seconds faster than the last, with inflation 3 to 5 psi above the normal setting. The aim is to reach temperature without shocking the tire through wheelspin, late braking or sliding. After that, the tire needs to cure for at least 24 hours, and a week is better.
That schedule is a manufacturer’s procedure for one tire line, not a universal rule. Follow the document for the tire you bought. The useful principle is that a new track tire’s first session is not the moment to chase a personal best.
Wet weather, pressure and wear
Tread clears water, and NHTSA treats a tire as unsafe once tread reaches 2/32 of an inch. NHTSA also says summer tires are not designed to operate in temperatures below freezing, or on snow and ice.
Hoosier is blunt about its streetable track tire. It meets DOT requirements, but it is not recommended in standing water where hydroplaning is possible, especially when shaved or worn. A tire with more tread is the safer wet-weather choice.
If rain is forecast, ask the organizer how the event handles it.
Track use raises tire pressure. Hoosier warns against bleeding hot tires down to cold set points. The tire will then be underinflated, which increases wear and can lead to separation.
For the road, use the vehicle manufacturer’s cold pressure from the door placard or owner’s manual, not the maximum printed on the sidewall. Our guide to the placard versus the sidewall number explains why they differ.
After the event, look for flat spots, blisters, cuts and unusual wear. The tread depth guide shows how to measure what is left.
A short selection process
- Read the organizer’s tech rules for tire condition and age.
- Match the tire to the season. Summer tires are not designed for freezing temperatures.
- Inspect tread, sidewalls and repairs before you leave home.
- Decide whether you need a street tire or a track-focused tire. The difference is covered in our slicks versus road tires comparison.
- If you choose a track tire, plan its break-in and cure time.
- Set cold pressures correctly and check them hot.
For the wider category differences, see touring versus performance tires. This guide sits in the Motorsports and Performance Driving hub.
Frequently asked questions
Can I do a track day on ordinary all-season tires?
Often yes, if they are in good condition. NASA Arizona says performance tires are not required to pass tech, and inspectors look for enough tread and sound sidewalls. Check your organizer’s rules before you enter.
Does a lower treadwear number mean more grip?
Not necessarily. The federal treadwear grade compares wear on a government course, not dry grip or lap time. A softer tire may wear faster, but the grade alone cannot rank dry grip.
Do new track tires need a break-in?
Track-focused tires often do. Hoosier’s procedure uses a short first session, a gradual increase in pace and a controlled cool-down, followed by at least 24 hours of cure time. Follow the maker’s instructions for your exact tire.
Can I drive home on track tires?
Check the maker’s documentation first. Hoosier says its TrackAttack Pro meets DOT requirements but is not recommended in standing water, especially when shaved or worn. Reset pressures to the road setting, and replace any tire with damage or insufficient tread.
