SAE grades such as 0W-20 and 5W-30 describe cold-start flow and hot-engine thickness. Learn what each number measures and why the manual's grade matters.
What do 0W-20 and 5W-30 mean?
The first number and letter describe cold-start behavior, and the second number describes viscosity at operating temperature. Neither number is an outside temperature, and neither is a “weight.”
A label such as 0W-20 or 5W-30 comes from SAE J300, the standard that sorts engine oils by flow behavior. SAE describes J300 as a classification “in rheological terms only.” In plain language, the grade measures how oil flows, not whether it protects a particular engine.
That is why the owner’s manual still decides. SAE says the grades are intended for engine manufacturers to choose what to recommend. The bottle gives the grade; the manual gives permission.
How SAE J300 builds a grade like 5W-30
J300 defines two series of grades. Grades that contain the letter W are defined by maximum low-temperature cranking and pumping viscosities, plus a minimum kinematic viscosity at 100 degrees C. Grades without a W are defined by a range of kinematic viscosities at 100 degrees C and a minimum high-temperature, high-shear viscosity measured at 150 degrees C.
A multigrade must meet all three criteria at once: the cold limits, a 100 degrees C viscosity inside one of the non-W ranges, and the high-temperature, high-shear minimum, as API’s Annex F lists them.
So 5W-30 is not two oils blended at the counter. It is one oil that passed a cold test series and a hot test series. The W does not mean weight. It marks the cold-weather number, and a lower figure means the oil is rated for colder conditions.
Kia’s 2026 K5 manual separates the two effects. It says oil viscosity affects fuel economy and cold-weather starting and flow, while higher-viscosity oil is needed for satisfactory lubrication in hot weather.
What the 20 and 30 halves measure
The second number is tied to kinematic viscosity at 100 degrees C, roughly the temperature of a warm engine. SAE’s revision notes for J300 give the 20 grade a range of 6.9 to 9.3 mm2/s and the 30 grade 9.3 to 12.5 mm2/s. The higher the number, the thicker the oil is when hot.
The grade also carries a high-temperature, high-shear minimum at 150 degrees C, a harsher test than plain kinematic viscosity. Two oils labeled 5W-30 can therefore be formulated differently and still meet the same grade. The label sets limits, not an identity.
| Label part | What it describes | Example | What it does not tell you |
|---|---|---|---|
| 0W, 5W, 10W | Low-temperature cranking and pumping limits | 0W is rated for colder conditions than 5W | The coldest weather your engine will see |
| 20, 30, 40 | Kinematic viscosity range at 100 degrees C | 20 is 6.9 to 9.3 mm2/s; 30 is 9.3 to 12.5 mm2/s | Whether your engine was designed for it |
| W | Cold-weather grade marker, not weight | 5W-30 | Anything about brand quality |
| API SP, ILSAC GF-6 | Performance and fuel-economy standards | Separate from the SAE grade | The viscosity grade by itself |
Two engines in one model can take different grades
The grade is assigned per engine, not per model name. The 2026 Kia K5 lubricants chart lists full synthetic SAE 0W-20 for the 2.5 GDi engine and full synthetic SAE 0W-30 for the turbocharged 2.5 T-GDi. Both entries also call for API SN PLUS/SP or ILSAC GF-6.
Two cars can look alike and still take different oil. Read the chart for your engine, not the badge on the trunk.
The manual also says to consider the temperature range the vehicle will be operated in before the next oil change, then choose from its chart. Use that instead of inventing your own winter rule.
What happens if you use the wrong grade
Kia’s manual states that using oils of any viscosity other than those recommended could result in engine damage. It also warns against engine-oil additives, because they can change the oil’s properties.
The trade-off runs both ways. A thinner oil can help fuel economy and cold starting. A thicker oil is specified where hot-weather lubrication demands it. Buying by habit ignores both sides.
For oil types rather than grades, see synthetic vs conventional motor oil. For where the specification is printed and what to record, see how to find your vehicle’s required oil specification. The Car Parts and Fluids hub covers other fluids.
A short checklist before you buy oil
- Find the viscosity chart for your model year and engine in the owner’s manual.
- Note every permitted grade and any conditional alternative.
- Match the API or ILSAC standard shown on the same chart.
- Check the bottle label for both the grade and the standard.
- Do not switch grades because a different one is on sale.
- Keep the receipt and record which grade went in.
If the manual allows an alternative only for a limited temperature range, use the primary grade whenever you can.
Frequently asked questions
Is 5W-30 thicker than 0W-20?
Yes at operating temperature. The 30 grade has a higher viscosity range at 100 degrees C than the 20 grade. The W halves describe cold behavior, so this is not a single-number comparison.
Can I use 5W-30 instead of 0W-20?
Only if your owner’s manual permits it. Some engines specify one grade with no alternative. A different grade can affect fuel economy, cold starting and, as Kia warns, engine durability.
Does the W stand for weight?
No. It marks the low-temperature series of grades, and the number in front of it is a cold-performance rating. It is not a weight in pounds or kilograms.
Do I need a different grade in summer and winter?
Use the grade your manual specifies. Some manuals allow another grade only within a stated temperature range. Follow that chart instead of changing grades by season.
