THE MOTOR ATLAS GUIDE

High-Voltage Safety Training for Automotive Workers

A certificate is not the training: safe high-voltage work needs OEM procedures, verified proficiency, PPE discipline and an employer energy-control program.

A high-voltage battery pack marked with a warning triangle sits on a bench with an orange cable, green insulating gloves and a red lockout padlock and tag.

Understand the shock, arc-flash and battery hazards of EV work, what OSHA requires and where NFPA 70E and ASE's xEV levels fit.

Quick answer: A certificate is not the training: safe high-voltage work needs OEM procedures, verified proficiency, PPE discipline and an employer energy-control program.

What high-voltage safety training has to cover

High-voltage training for automotive workers must explain electric shock, arc flash and battery hazards, and it must be tied to the vehicle and task. A general awareness video is not enough for someone who will disconnect a traction battery. OSHA, ASE and the manufacturer each supply part of the requirement.

This article summarizes published standards. It is not a substitute for your employer’s training, the OEM procedure for the vehicle, or hands-on instruction from a qualified trainer.

The automotive careers hub lists related guides.

The hazards are wider than a shock from one wire

Hazard What the standards describe Primary control
Electric shock ASE calls shock the most likely hazard; electrocution can result from as little as 30 volts, and systems above 30 volts AC or 60 volts DC are treated as dangerous De-energize, verify and use a qualified person
Muscle lock-on Current in the 6 to 16 milliamp range can prevent a worker from letting go and cause a fall Work de-energized; use the one-hand rule when testing
Arc flash and arc blast An arc can reach 35,000 degrees Fahrenheit, expel molten metal at more than 740 mph and produce toxic smoke Arc-rated PPE, barriers and a justified live-work plan
Battery fire and stored energy ASE’s standards cite battery fires as a major potential hazard, and damaged packs add arc-flash risk; an isolated battery still holds energy OEM isolation, storage rules and an emergency plan for damaged or flooded vehicles

What OSHA requires

The electrical training rule at 29 CFR 1910.332 applies to employees who face a risk of electric shock that the installation itself does not remove. Its Table S-4 lists mechanics and repairers among occupations with a higher than normal risk. Employees must be trained in the safety-related work practices in 1910.331 through 1910.335 that apply to their jobs. Qualified persons need additional training in identifying live parts, determining nominal voltage and keeping the required clearance distances.

The work-practice rule at 1910.333 requires live parts to be de-energized before work unless the employer can show that de-energizing is infeasible or creates a greater hazard. For fixed equipment, it requires lockout or tagout and verification by a qualified person. Only qualified persons may work on parts that have not been de-energized.

The general lockout/tagout standard at 1910.147 adds a written energy-control program, employee training, an annual inspection and retraining when equipment or procedures change. It expressly excludes electrical hazards in electric-utilization installations, which Subpart S covers.

1910.269 covers power generation and distribution, not vehicle repair, so a shop should not claim it as the EV standard.

NFPA 70E does not cover the vehicle

NFPA 70E is often named in EV safety classes, but the 2024 edition says it does not cover installations in “automotive vehicles other than mobile homes and recreational vehicles” (70E 90.3(B)(1)). It is written for workplace electrical equipment, not a car’s traction system.

That does not make it irrelevant. ASE uses an NFPA 70E arc class when specifying face shields, and a shop may apply 70E ideas to chargers and fixed equipment. For the vehicle itself, follow OSHA’s electrical rules, the ASE xEV standards and the OEM procedure.

What the ASE levels mean

Level Who it covers Work described in the standard
Level 1, Electrically Aware Person Sales, service and repair staff near an xEV Drive the vehicle, do non-high-voltage work and handle non-high-voltage parts; must not touch the service disconnect or high-voltage components
Level 2, High-Voltage Vehicle Technician A trained service professional Evaluate the high-voltage battery and system, isolate voltage, secure the system, restart it and work on de-energized components
Level 3, High-Voltage Vehicle and Battery Technician A Level 2 technician with battery-pack training Work inside the battery, separate modules and perform live work where necessary

ASE offers public tests for Levels 1 and 2. The Level 1 test has 20 questions and the Level 2 test has 30. ASE’s standards also define Level 3; the public test page lists only Levels 1 and 2 (ASE xEV).

What a credible employer program includes

A certificate does not prove safe work on a specific vehicle. ASE’s shop section requires documented training, verification of each person’s ability to use test equipment, PPE logs and a defined work area (ASE standards). Ask whether the program includes:

  • The OEM de-energizing procedure for each vehicle family, including the wait before touching terminals.
  • An absence-of-voltage check with a CAT-rated meter and a live-dead-live sequence.
  • Class 0 insulating gloves with current test dates, leather over-gloves, arc-rated clothing, eye protection and insulated tools.
  • Barriers, signs and a rule that no one works alone on a high-voltage vehicle.
  • Emergency response, first aid and CPR, including how to separate a victim without touching them.
  • Retraining when a new model, tool or procedure changes the job.

If the employer cannot show the procedure, PPE log and verification step, training is incomplete.

Frequently asked questions

Is ASE xEV certification enough to work on high-voltage batteries?

No. ASE tests knowledge, but its standards say the employer must verify proficiency and the technician must follow the OEM procedure. Level 2 covers general de-energized work; work inside the pack is Level 3 territory.

Does NFPA 70E apply to EV repair?

Not to the vehicle. NFPA 70E’s scope excludes automotive vehicles other than mobile homes and recreational vehicles. It can still inform shop electrical work and PPE selection, but it is not the standard for a traction battery.

How long is ASE xEV certification valid?

Five years. The Level 1 test has 20 questions and the Level 2 test has 30, each with a 60-minute limit. Check ASE’s registration page for current dates.

Can an employer assign high-voltage work without training?

OSHA requires training for employees exposed to electrical risk and limits energized work to qualified persons. A shop that assigns high-voltage work without documented training and verification is not following those rules.

How this guide was prepared: Researched explanatory guidance using the sources linked on this page. We have not road-tested a vehicle or completed a hands-on inspection for this article. The displayed byline is a fictional editorial persona, not a real individual author or certified technician reviewer. Motor Atlas is responsible for this content. Confirm vehicle-specific procedures with the manufacturer, and ask an appropriate professional before safety-critical repairs, legal filings or financial decisions.

Related reading